Цитата:
|
Сообщение от dimon73
umount /dev/sdb1
mkfs -t ext2 -I 128 /dev/sdb1
Потом пробуй дальше в ES ставить.
|
Лог в Путти:
Welcome to Cuberevo
cuberevo login: root
Password:
[PGI ~]$ umount/dev/sdb1
-sh: umount/dev/sdb1: not found
[PGI ~]$ mkfs -t ext2 -I 128 /dev/sdb1
mke2fs 1.41.9 (22-Aug-2009)
/dev/sdb1 is mounted; will not make a filesystem here!
Чёртова флешка не отмонтируется !
После третьей попытки получилось вот что :
Welcome to Cuberevo
cuberevo login: root
Password:
[PGI ~]$ fdisk -l
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 125 1004031 83 Linux
/dev/sda2 126 121601 975755970 83 Linux
Disk /dev/sdb: 1009 MB, 1009778688 bytes
32 heads, 61 sectors/track, 1010 cylinders
Units = cylinders of 1952 * 512 = 999424 bytes
Disk /dev/sdb doesn't contain a valid partition table
[PGI ~]$
umount/dev/sdb1
-sh: umount/dev/sdb1: not found
[PGI ~]$
mkfs -t ext2 -I 128 /dev/sdb1
mke2fs 1.41.9 (22-Aug-2009)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
61696 inodes, 246520 blocks
12326 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=255852544
8 block groups
32768 blocks per group, 32768 fragments per group
7712 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376
Writing inode tables: done
Writing superblocks and filesystem accounting information: done
Что дальше делать в ES? по инструкции ?
вот лог:
connect 192.168.0.4..
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
Disk /dev/sdb: 1009 MB, 1009778688 bytes..
umount: can't umount /tmp/e2: Invalid argument
fdisk /dev/sdb..............
Fdisk is ok...
Writing inode tables: 0/81/8..
Writing superblocks and filesystem accounting information:
6/87/8done
format is ok...
[PGI ~]$ chmod 777 /tmp/e2..
Available on mount.dev: 927404....
Disk.Info: .
d
f
-h && fdisk -l
Filesystem Size Used Available Use% Mounted on
/dev/root 17.9M 17.9M 0 100% /
none 32.5M 68.0K 32.4M 0% /tmp
none 32.5M 0 32.5M 0% /mnt
none 32.5M 72.0K 32.4M 0% /dev
tmpfs 32.5M 0 32.5M 0% /dev/shm
/dev/mtdblock4 10.0M 7.2M 2.8M 72% /var
/dev/sda2 930.5G 51.5G 832.4G 6% /media
/dev/sdb1 955.0M 1.2M 905.7M 0% /tmp/e2
Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 125 1004031 83 Linux
/dev/sda2 126 121601 975755970 83 Linux
Disk /dev/sdb: 1009 MB, 1009778688 bytes
32 heads, 61 sectors/track, 1010 cylinders
Units = cylinders of 1952 * 512 = 999424 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 * 1 1010 985729+ 83 Linux
[PGI ~]$
File: bar5usb_9000.tar.gz..
Connecting to 192.168.0.4:21
C:\Enigma2\IscanMod\bar5usb_9000.tar.gz write............
Transfert succesful. File is C:\Enigma2\IscanMod\bar5usb_9000.tar.gz
unpack tar...
..
Available on mount.dev: 829360....
Set nameserver is 192.168.0.1
Set IP: 192.168.0.4............
correct fstab.........
set video to hdmi......
Надо ли править загрузчик или родной (PGI) можно использовать?
Есть ли какая -нибудь команда проверить загрузчик?
Нашел, вот лог; все ли нормально не знаю подскажите:
Welcome to Cuberevo
cuberevo login: root
Password:
[PGI ~]$ fw_printenv
preboot=edb toenv ethaddr;bootmenu
menu_timeout=echo booting...;front_puts "booting";boot
menu_serialbreak=echo entering boot loader console.;front_puts "console"
menu_upgusb=setenv stdout vga;setenv stderr vga;if usbupg; then reset; else echo Oops...; echo You can debug through serial port.; fi
menu_upgserial=setenv stdout vga;setenv stderr vga;serial_upgrade;reset
menu_set2set=setenv stdout vga;setenv stderr vga;serial_set2set;reset
menu_hddfmt=setenv bootargs $bootargs format_hdd=1;front_puts "format hdd";boot
menu_debugmode=setenv bootargs $bootargs debug debug_app=1;front_puts "debug she ll";boot
menu_upgnet=setenv bootargs $bootargs factory_update=1;front_puts "net upg";boot
menu_tvmode=set_tvmode;boot
serial#=cuberevo debugging
monitor_base=0xA0000000
monitor_len=0x00040000
monitor_sec=1:0
load_addr=0x84000000
unprot=protect off $monitor_sec
update=erase $monitor_sec;cp.b $load_addr $monitor_base $monitor_len;protect on $monitor_sec
menu_upgusbhost=setenv stdout vga;setenv stderr vga;if usbupghost; then reset; e lse echo Oops...; echo You can debug through serial port.; fi
menu_1=front_puts ENIGMA-FLASH;setenv bootargs "console=ttyAS1,115200 root=/dev/ mtdblock3 rootfstype=jffs2 rw coprocessor_mem=4m@0x10000000,4m@0x10400000";seten v bootcmd "bootm a0060000";saveenv;boot
menu_2=front_puts ENIGMA-SDA;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sda1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m @0x10400000";setenv bootcmd "run bootusb";saveenv;boot
menu_3=front_puts ENIGMA-SDB;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sdb1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m @0x10400000";setenv bootcmd "run bootusb";saveenv;boot
ipaddr=192.168.1.8
serverip=192.168.1.1
gateway=192.168.1.1
netmask=255.255.255.0
menu_0=front_puts DGS-FLASH;setenv bootargs "console=ttyAS1,115200 panic=3 root= /dev/mtdblock3 bigphysarea=1500 quiet";setenv bootcmd "bootm a0060000";saveenv;b oot
menu_4=front_puts ENIGMA2-FLASH;setenv bootargs "console=ttyAS1,115200 panic=3 r oot=/dev/mtdblock3 bigphysarea=10240 mem=128m coprocessor_mem=4m@0x10000000,4m@0 x10400000 ip=$ipaddr:$serverip:$gateway:$netmask quiet";setenv bootcmd "bootm a0 060000";saveenv;boot
menu_5=front_puts ENIGMA2-SDA3;setenv boothdd "run bootargshdd;ide reset;ext2loa d ide 0:3 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargshdd "setenv bootar gs console=ttyAS1,115200 panic=3 root=/dev/sda3 rw rootdelay=10 init=/bin/devini t ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000, 4m@0x10400000";setenv bootcmd "run boothdd";saveenv;boot
menu_6=front_puts ENIGMA2-SDA4;setenv boothdd "run bootargshdd;ide reset;ext2loa d ide 0:4 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargshdd "setenv bootar gs console=ttyAS1,115200 panic=3 root=/dev/sda4 rw rootdelay=10 init=/bin/devini t ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000, 4m@0x10400000";setenv bootcmd "run boothdd";saveenv;boot
menu_7=front_puts ENIGMA2-SDA5;setenv boothdd "run bootargshdd;ide reset;ext2loa d ide 0:5 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargshdd "setenv bootar gs console=ttyAS1,115200 panic=3 root=/dev/sda5 rw rootdelay=10 init=/bin/devini t ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000, 4m@0x10400000";setenv bootcmd "run boothdd";saveenv;boot
menu_8=setenv bootargs $bootargs boot_pause=1;front_puts "boot pause";boot
menu_9=setenv bootargs $bootargs restore_backup=1;front_puts "RESTORE BKUP";boot
boothdd=run bootargshdd;ide reset;ext2load ide 0:8 a5ff0000 boot/uImage;bootm a5 ff0000
bootargshdd=setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sda8 rw root delay=10 init=/bin/devinit ip=192.168.1.8:192.168.1.1:192.168.1.1:255.255.255 .0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000
bootusb=run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5 ff0000
bootargsusb=setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sdb1 rw root delay=10 init=/bin/devinit ip=192.168.1.8:192.168.1.1:192.168.1.1:255.255.255 .0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000
stdin=serial
stdout=serial
stderr=serial
ethaddr=00:13:18:02:46:30
bootargs=console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 bigphysarea=1500 quie t
bootcmd=bootm a0060000
[PGI ~]$